{"id":1058,"date":"2012-02-26T20:39:00","date_gmt":"2012-02-27T04:39:00","guid":{"rendered":"https:\/\/sixstringsensei.com\/?p=1058"},"modified":"2023-10-22T12:14:53","modified_gmt":"2023-10-22T19:14:53","slug":"guitar-buffer-pedal-knowledge-true-bypass-vs-buffered-pedals","status":"publish","type":"post","link":"https:\/\/sixstringsensei.com\/1058\/guitar-buffer-pedal-knowledge-true-bypass-vs-buffered-pedals\/","title":{"rendered":"Guitar Buffer Pedal Knowledge – True Bypass vs Buffered Pedals"},"content":{"rendered":"

The third and last part of the Six String Sensei Absolute One Stop Guide to the Guitar Pedal Board has to do with true-bypass vs. buffered pedals and location options for a guitar buffer pedal – A VERY debated subject.<\/h3>\n

In the previous feature on guitar effects pedal order we focused on the general rules for best results when setting up the order of your pedals.\u00a0 When it comes to whether true-bypass or buffered pedals are best, the order of your pedals is a VERY important factor to consider. Mainly, to establish where in the chain you want buffers.<\/p>\n

But, before we continue, let\u2019s establish what true-bypass and buffered pedals are:<\/strong>
\n
\nTrue-bypass pedal:<\/strong> A true-bypass pedal is one that completely and mechanically disconnects your guitar\u2019s lead signal from the pedals circuit so that none of it is touching the pedal\u2019s circuit.<\/p>\n

Buffered pedal:<\/strong> Put simply, a buffer for guitar is an electronic device that takes a high-impedance signal and converts it into a low-impedance signal. Pedals that are not true-bypass generally have a buffer to convert the signal of your guitar from high-impedance to low-impedance.<\/p>\n

While it\u2019s a little past the scope of this feature, it should be mentioned that many pedals throughout the years have claimed to be true-bypass, but many really are not. Oftentimes, the switch in the pedal opens the circuit at the end of the circuit board while closing the connection of the guitar signal to let the signal through. Unfortunately, at the beginning of the circuit board, the signal is still \u201ctouching\u201d the pedal\u2019s circuits even though the signal it cannot make it all the way through.<\/p>\n

The result of this is what\u2019s typically known as tone-sucking<\/em>. That\u2019s when a pedal sucks tone out of your guitar even when it\u2019s turned off. To effectively have true-bypass, your guitar\u2019s signal needs to be completely disconnected from the effects-pedal circuit a both the beginning AND the end of the circuit. This is usually done with a 3PDT (3 pole double throw switch) to allow for the activation of an LED. Not all true-bypass pedals use a 3PDT switch – Many modern pedals (like the DigiTech Hardwire pedals) effectively do the same thing using a more sophisticated relay switching system. You can\u2019t easily see it in work, but it is true-bypass.<\/p>\n

On to what\u2019s best. True-bypass or buffers<\/strong><\/p>\n

Now, I\u2019m not here to act like the supreme overlord of technical guitar jargon. I\u2019m not going to act like a scientist and give you a bunch of complicated numbers that will only cause confusion. (I\u2019m not saying you\u2019re dumb either). But let\u2019s simplify it a bit and talk in easy to remember terms\u2026 [Even if the technical know-it-alls of the guitar world decide to flame me.]<\/p>\n

The signal that comes from your guitar is high-impedance and a buffered signal is low-impedance.<\/em><\/strong><\/p>\n

Don\u2019t get confused thinking that the \u201chigh\u201d impedance signal is stronger and more stable than the \u201clow\u201d impedance signal. It\u2019s the other way around! The low impedance signal is stronger, more stable and the chances of it losing quality are less.<\/p>\n

The trick I use to remember that is to remind myself that \u201cimpedance\u201d comes from the word \u201cimpede\u201d which means, according to Mr. Webster, \u201cto interfere with or slow the progress of.\u201d<\/em><\/p>\n

To help it make even more sense\u2026 Here\u2019s another way of liking at it: If the signal has low-impedance <\/em>that means it\u2019s a signal that has low interference.<\/strong> Easy enough, right? Good!<\/p>\n

The same way an electrical current loses power due to something called capacitance (where the density of conductive material sucks up some of the power), the weak high-impedance signal coming from your guitar pickups is very susceptible to capacitance and therefore, tone loss. The longer your signal chain, the worse. In other words, the more metal (cables, switches, circuits) the more the high-impedance signal is going to suffer.<\/p>\n

By the time the signal gets there it\u2019ll be huffing and puffing like a smoker with asthma running a marathon.<\/p><\/blockquote>\n

Think about it this way\u2026 If you use a 25 foot guitar cable that allows you to jump around on-stage like an epileptic monkey, and you have 10 true-bypass effects pedals on your board, and another 25 feet of cable from the board to the amp, that\u2019s effectively over 55 feet of cable if you factor in the patch cables on the actual pedalboard. If all the pedals are off, you have a weak high-impedance signal coming out of your guitar pickups, which is having a dang hard time trying to make it past 55 feet of cable all the way to your amp. By the time the signal gets there it\u2019ll be huffing and puffing like a smoker with asthma running a marathon. Therefore, you get tone-loss \u2013 and lots of it.<\/p>\n

To make matters worse, you then turn on one of your pedals and the signal gets stronger from there on after effectively raising the volume of your guitar and messing with the tone. For that reason, it\u2019s important that some sort of guitar buffer pedal is placed somewhere in the signal chain to help stabilize it, and to help with long cable runs.<\/p>\n

The reason true-bypass pedals are great is because most of the time buffers tend to color your signal. Of course, this depends on the quality of the buffer. \u00a0Some buffered guitar pedals yield a noticeable change in tone, while others are nearly transparent. The problem is that many guitarists that don\u2019t have a good ear for tonal changes take the easy route and simply use a catch-all and tag all buffers as evil. The better way to go about it would be to A\/B test various buffered pedals and listen for tone coloring. Then compare that to some true-bypass pedals. The bottom line is you want to sound good.<\/p>\n

Balance is the key<\/strong><\/p>\n

But, no matter what, if ALL your pedals are buffered you are effectively increasing the chance of unwanted tone-coloring and the possible introduction of noise from all those buffering units. This is because the adverse effects of multiple buffers (and any other type of signal coloring culprits) are cumulative. So, the key here is to find the right balance between buffered and true-bypass pedals.<\/p>\n

Buffers can be standalone or as part of a pedal. For example, the famous Boss TU-12 tuner is a common pedal in the beginning of many guitarists effects chain. That pedal has a pretty good buffer – Nothing amazing, but certainly not bad either. More discerning guitarists will often buy a dedicated buffer that they can test at different points in the chain for the results they are chasing.<\/p>\n

Now this is when things get hairy. Go to any guitar forum, search for threads about buffers and you\u2019ll go crazy trying to figure out what to do. Some guitarists recommend a buffer at the beginning of your board, some recommend it at the end, while still others recommend two, one at the beginning and the other at the end before the cable run to the amp.<\/p>\n

In the pedalboard I used as an example in the first part of the Absolute Guitar Pedal Board Guide, the very first pedal in the chain is a dedicated custom-made buffer. The cool thing is, it has a true-bypass switch, so it allows me to turn the buffer on and off to test the difference. Haha. So essentially, it is a true-bypass buffer \u2013 How\u2019s that for ironic and confusing?<\/p>\n

\"True<\/a>
In our example pedalboard, the signal enters the buffer (top-right) and goes through all true-bypass pedals. It then exits the MXR EVH Phase 90 buffered pedal before it heads out to the amps. The DigiTech Delay\/Looper runs in the amps effects loop.<\/figcaption><\/figure>\n

Let\u2019s talk about the reasoning behind the location of the guitar buffer pedals.<\/strong><\/p>\n

    \n
  1. Buffer 1st<\/sup> in the chain<\/strong> \u2013 The benefit of this location is that it feeds all your pedals with the same, strengthened low-impedance signal. As soon as a pedal is turned on, the output of that pedal is responsible for the rest of the signal chain. But as soon as the pedal(s) is off, the load goes back to the buffer. This is a very popular buffer location. However, this location doesn\u2019t come without any perils. Keep in mind that certain fuzz and distortion boxes, namely the ones that use germanium diodes work better with the direct high-impedance signal of the guitar. For pedals like these, it\u2019s better to put the buffer right after them, even if it\u2019s still near the beginning of the chain. That\u2019s another benefit of having a buffer with a switch, it can be turned off before running a fuzz box. But of course, if you will be using the fuzz box a lot, might as well just put the buffer AFTER it and leave it on all the time.<\/li>\n
  2. In the middle of the chain<\/strong> \u2013 This is sort of what I was talking about near the end of the first point. Oftentimes, you have pedals that don\u2019t sound good with a buffered signal. For those you can just move the buffer further down the chain. If you have a couple of germanium pedals and a wah that you prefer the sound of without buffering, by default your buffer will end up near the middle of the chain. Done deal.<\/li>\n
  3. Buffer at the end of the pedal chain only<\/strong> \u2013 This setup means that the entire signal goes from your guitar, through all-true-bypass pedals and runs into a buffer right at the end of the pedalboard before the signal heads out to the amps. The logic behind this setup is that the effects pedal chain is completely unaffected by buffers, but then right after the last effects pedal, the signal is \u201cstrengthened\u201d to make it\u2019s final run to the amps. This setup is particularly good for smaller pedalboards with long cable runs back to the amps on a big stage. The pedal chain is short, so there\u2019s very little worry of tone suck between the guitar and the pedals. Then, the buffer is used to help avoid tone suck between the board and the long cable travel to the amps.<\/li>\n
  4. Buffer at the beginning and end of the pedal chain<\/strong> \u2013 This setup is quite popular and it\u2019s the one I prefer. It gives you a nice strong low-impedance input to all your pedals and then the signal is again buffered at the end of the pedal chain before it goes to do it\u2019s long voyage to the amps. Some guys run dedicated buffers at the beginning and end. But, if you take a close look at my sample board, the first buffer that sits right at the beginning, is the dedicated custom buffer with true-bypass switch that I mentioned earlier. The last buffer is actually the one provided by the non-true-bypass MXR EVH Phase 90 that\u2019s at the end of the board.\u00a0 I know what you might be thinking, \u201cThat\u2019s a mass production pedal and the buffer is not as good as that of a custom dedicated buffer.\u201d Maybe true, but I can\u2019t tell a difference and it works quite well. Sometimes, I take off the Phase 90 and put a true-bypass MXR Carbon Copy, which effectively turns the setup back into at \u201cbuffer at the beginning only\u201d rig. Seems to work just fine too, but I\u2019m not running super long cables to the amp either.<\/li>\n<\/ol>\n

    That\u2019s about it for buffers vs true-bypass. This is always a topic with never-ending debates. There is more than one \u201cright way\u201d of going about it. However, after hours and hours of research, you\u2019ll find that most experts agree that true-bypass pedals are best but when combined with some sort of buffering system. The type of buffer unit, and buffer unit location you choose will ultimately depend on the type of effects pedals you are running and personal preference. The best results are really almost always found by experimenting. But it\u2019s great when you know certain rules of thumb. It will help keep your experiments in check.<\/p>\n

    If you are pretty much set on wanting a true-bypass distortion pedal for example, check out the Fulltone OCD, it\u2019s by far one of my favorite true-bypass distortion pedals. See the link below:<\/p>\n